NON-SKID PAINT - Product Overview
TEXTURED EPOXY COLOR COATING (Call us for colors not listed, we might have them in stock)
Is a marine grade(one part) super tough Water Based Epoxy with Grit textured color coating. Contains a synthetic grit with no sharp edges, and is non abrasive to bare feet.
Specifically designed to provide a slip resistant durable textured surface for firmer
footing under wet and dry surface conditions. NON-SKID PAINT can be applied to
magnesite decking, concrete, wood, fiberglass, steel and treated aluminum.
Non-Skid Paint is perfect for metal surfaces such as Auto Haulers, Auto Lifts, Aluminum Ramps, Lift Gates, and Approach Plates. It is a product that will not harm the environment when used as directed.
COLORS IN STOCK:
CLEAR, WHITE, BLUE, BLACK, SHIPSTONE GRAY, CHAMIOS BEIGE, OSHA
YELLOW, OSHA ORANGE
SPECIAL ORDER COLORS:
BUTTERNUT, SEQUOIA GREEN, RUSSET RED, UMBER BROWN
It is recommended to use NON-SKID PAINT in (WHITE) to add too another color to achieve a lighter shade in that same color.
For color consistency use a 2 to 1 ratio.
Example: for every 2 gallons of chosen color NON-SKID PAINT add 1 gallon of
(WHITE) NON-SKID PAINT.
300 SQUARE FEET PER GALLON @ 4 MILS WET = 1.5 MILS DRY
(A two-coat application is recommended for most surfaces, and easy to apply with a brush or roller.)
Temperature and Humidity Dependent
(Apply in temperatures between 60 to 90 degrees.)
@ 77 DEGREES *F with 50% RELATIVE HUMIDITY
(Avoid painting late in the day when condensation is likely or if rain is forecasted)
TO THE TOUCH
30 40 Minutes TACK FREE
RECOAT or TOPCOAT..............
2 3 HOURS
..5 7 DAYS
CLEAN UP INFORMATION:
CLEAN HANDS AND TOOLS IMMEDIATELY WITH SOAP AND WARM WATER.
HELPFUL TIPS and Frequently asked Questions!:
DO NOT USE:
On garage floors or other areas where vehicles are parked OR on smooth glossy surfaces such as ceramic tile.
DO NOT USE:
I areas where there is continuous standing water or where ponding and puddling occurs. These areas must be leveled prior to use of NON-SKID PAINT.
HOW DO I CLEAN THE AREA PRIOR TO PAINTING?:
For Gelcoat and Fiberglass use Acetone. For Non-Ferrous Metals and Aluminum use a Industrial Degreaser and aluminum acid-etch preperation. On Concrete use Trisodium Phosphate (TSP), use a firm bristle brush and rinse off thoroughly with clean water. Area must be completely dry before application. If necessary, use a heat source such as a large Hot Air Dryer. These products are available through most Hardware Stores.
Do I need to add Monster Grit Pumice Additive?
NO, Non-Skid Paint comes pre-mixed with Grit. Extra Grit Additive is sometimes recommended for applications such as Incline Ramps, and Stadium Steps. See SKU:MP-MGPI-260
Can I use any kind of thinner?
NO, Non-Skid Paint is a Water Reducible Epoxy-Ester Coating and can only be thinned with water. Add no more than ½ quart of water per gallon for first coat only. (NOTE: Topcoat must be applied directly from pail without thinning)
Why do I need to stir Non-Skid Paint so thoroughly and not just shake it up real good?
The Grit material in Non-Skid Paint settles to the top of can, and sometimes sticks to the lid. This is because the Grit is lighter than the Epoxy and will stay suspended and not sink to the bottom of can after thoroughly mixed. Its best to scrap any Grit that is stuck to the lid back into the paint with a wood stir-stick; so as to not loose the normal textured surface. Mix well before and during application.
How do I clean Non-Skid Paint off my hands and tools?
Non-Skid Paint is environmentally safe to use. Easily clean hands and tools with warm soapy water immediately after application.
How long will it last before I need to recoat?
It is recommended that on high traffic areas you recoat once a year. On areas that do not get a lot of high traffic you can recoat once every two years as needed.
Whats the best way to keep Non-Skid Paint clean?
Clean Non-Skid Paint with warm water mixed with any mild soap or detergent. Use a firm bristle brush and rinse off thoroughly with clean water.
Do I need to apply a primer?
Non-Skid Paint is self-priming on Fiberglass, Gelcoat, Epoxy, Magnesite Decking, and Concrete surfaces. On wood substrates use a exterior oil base or latex wood primer. For metal surfaces apply an exterior metal primer over clean, dry metal. This will also provide additional rust prevention.